This model uses a liquid crystal display (LCD) of amorphous silicon TFT as switching components. This model is composed of a TFT LCD panel, a driver circuit, and an ass’y KIT of source PBA. This 32.0” model has a resolution of a 1366 x 768 and can display up to 16.7 million colors with the wide viewing angle of 89° or a higher degree in all directions. This panel is designed to support applications by providing a excellen performance function of the flat panel display such as home-alone multimedia TFT-LCD TV and a high definition TV.
RoHS compliance (Pb-free)
High contrast ratio & aperture ratio with the wide color gamut
SVA (Super vertical align) mode
Wide viewing angle (±178°)
High speed response
HD resolution (16:9)
DE (Data enable) mode
The interface (1Pixel/clock) of LVDS (Low voltagedifferential signaling)
| Item | Specification | Unit | Note |
| Active Display Area | mm | ||
| Switching Components | a-Si TFT Active matrix | ||
| Glass size | TFT: 713.0(H) x 410.5(V)CF:713.0(H) x 408.2(V) | mm | |
| Panel Size | 713.0(H) x 410.5(V) | mm | —0.5. 16:9 |
| 1.30(D) | mm | ||
| Weight | 800 (Typ) | g | |
| Display Colors | 16.7M (True Display) | ||
| Number of Pixels | 1,366 × 768 | ||
| RGB Horizontal Stripe | mm | ||
| Normally Black | |||
| Haze | 2.3% | ||
| Hard coating 2H |
| Item | Test Condition | Quantity | Note |
| HTOL | 50 ഒ, 500hr | 10 | |
| LTOL | -5 ഒ, 500hr | 3 | |
| THB | 50 ഒ / 90 %RH(500hr) | 3 | |
| Decompression | -40~50ഒ, 0m(0ft) ~ 13,700m(45,000ft), 72.5Hr | 3 | |
| HTS | 70 ഒ, Storage | 3 | |
| LTS | -25 ഒ, Storage | 3 | |
| Transportationcondition | drop(20cm) → temperature/humidity(-30~60ഒ / 40ഒ 90%RH)→ pressure → vibration(5~200Hz 1.05Grms, 2hr) → drop(20cm) | 1pallet | |
| WHTS | 60 ഒ / 75 %RH , Storage | 3 | |
| Noise | Electromagnetic noise: Overall 23dB | 2 | |
| Complex stress | -20ഒ ~60ഒ, 0~90%RH, 2cycle | 4 | |
| ESD | S-IC Input ±7KV, Output ±4KV | 3 |
[ Criteria on evaluation]
There should be no change of the product, which may affect to the practical display functions, when the display quality test is executed under the normal operation setting.
* HTOL/ LTOL : The operating cycle on the high and low temperature
* THB : Temperature humidity slant
* HTS/LTS : The storage at the high and low temperature
* WHTS : The storage in the high temperature with the high humidity
1. Carton
(1) Packing Form: Corrugated Card board box as shock absorber.
(2) Packing Method
(3) Packing Material
| 32" | Weight | Q’ty / PLT | Total Weight | |
| g | pcs | Kg | ||
| Packing Tray | 1056 | 20 | 294.61 | |
| Pallet | 1288 * 914 * 132 | 21000 | 1 | |
| Panel | 713.0 * 410.5 * T1.2 | 800 | 300 | |
| Tray | 894 * 634 * 40 | 590 | 2 | |
| 752.5 * 487 * T1.0 | 14.75 | 360 | ||
| - | 60 | 80 | ||
| 1282 * 908 * 120 | 1200 | 1 | ||
| Stack Layer | Max(Possible to be stacked 2levelsin warehouse) | 2 | Pallet | |
| Total Size | 1288 * 914 * 1197 | |||
2. Marking
A nameplate is affixed to the specified location on each product.
(4) Nameplate Indication
(5) Packing box attach
1. Handling
(a) When the panel kit and BLU kit are assembled, the panel kit and BLU kit should be attached to the set system firmly by combining each mounted holes. Be careful not to give the mechanical stress.
(b) Be careful not to give any extra mechanical stress to the panel when designing the set, and BLU kit.
(c) Be cautious not to give any strong mechanical shock and / or any forces to the panel kit. Applying the any forces to the panel may cause the abnormal operation or the damage to the panel kit and the back light unit kit.
(d) Refrain from applying any forces to the source PBA and the drive IC in the process of the handling or installing to the set. If any forces are applied to the products, it may cause damage or a malfunction in the panel kit.
(e) Refrain from applying any forces which cause a constant shock to the back side of panel kit, the set Design and BLU kit. If any forces are applied to the products, it may cause an abnormal display, a functional failure and etc.
(f) Note that polarizer could be damaged easily.
(g) Wipe off water droplets or oil immediately. If you leave the droplets for a long time on the product, a staining or the discoloration may occur.
(h) If the surface of the polarizer is dirty, clean it using the absorbent cotton or the soft cloth.
(i) Desirable cleaners are water or IPA (Isopropyl Alcohol). Do not use Kenton type materials (ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride. These might cause the permanent damage to the polarizer due to chemical reaction.
(j) If the liquid crystal material leaks from the panel, this should be kept away from the eyes or mouth. If this contacts to hands, legs, or clothes, you must washed it away with soap thoroughly and see a doctor for the medical examination.
(k) Protect the panel kit and BLU Kit out of the static electricity. Otherwise the circuit IC could be damaged.
- Reference : Process control standard of SDC
| No. | Item | Control standard |
| 1 | Ionizer | All Equipment should be controlled under 150V.(Typ. 100V) |
| 2 | Carrying Roller | Carrying Roller should be controlled under 200V. |
| 3 | Equipment Ground Resistance | All Equipment Ground Should be less than 1ohm. |
(l) Remove the stains with finger-stalls wearing soft gloves in order to keep the display clean in the process of the incoming inspection and the assembly process.
(m) Do not pull or fold the source drive IC which connects to the source PBA and the panel or the gate drive IC.
(n) Do not pull, fold or bend the source drive IC and the gate drive IC in any processes. If not, the source drive IC could be bent one time in the process of assembling the panel Kit and the BLUKit.
(o) Do not adjust the variable resistor located on the panel kit and BLU kit except when adjusting the flicker.
(p) Do not touch the pins of the interface connector directly with bare hands.
(q) Be cautious not to be peeled off the protection film.
- Make sure to peel off slowly (It is recommended to peel it off at the speed of more than 8sec. constantly.)
- The peeling direction is shown at the Fig
- Instruct the ground worker to work with the adequate methods such as the antistatic wrist band.
- Maker sure to be grounded the source PBA while peeling of the protection film.
- Ionized air should be blown over during the peeling
- The protection film should not t be contacted to the source drive IC.
- If the adhesive stains remain on the polarizer after the protection film is peeled off, please move stains with isopropyl-alcohol liquid.
(r) The protection film for the polarizer on the panel kit should be slowly peeled off just before using so that the electrostatic charge can be minimized.
(s) The panel kit and BLU kit have high frequency circuits. The sufficient suppression to the EMI should be done by the set manufacturers.
(t) The set of which the panel is assembled shall not be twisted. If the product is twisted, it may cause the damage on the product.
(u) Surface Temp. of IC should be controlled less than 100ଇ, operating over the Temp. can cause the damage or decrease of lifetime.
2. Storage
The storage condition for packing
| ITEM | Unit | Min. | Max. | ||||||
| Storage Temperature | (ଇ) | 5 | 40 | ||||||
| StorageHumidity | (%rH) | 35 | 75 | ||||||
| Storage life | 6 months | ||||||||
| Storage Condition | (1) The storage room should provide good ventilation and temperature control. (2) Products should not be placed on the floor, but on the Pallet away from a wall. (3) Prevent products from direct sunlight, moisture nor water; Be cautious of a buildup of condensation. (4) Avoid other hazardous environment while storing goods. (5) If products delivered or kept in conditions of the recommended temperature or humidity, we recommend you leave them at a circumstance which is shown in the following table. | ||||||||
| period | 1 month | 2 months | 3 months | 4 months | 5 months | 6 months | |||
| Baking Condition | No Baking | 50ଇ, 10% 24Hr | 50ଇ, 10%, 48Hr | ||||||
3. Operation
(a) Do not connect or disconnect the FFC cable during the "Power On" condition.
(b) Power supply should be always turned on and off by the "Power on/off sequence"
(c) The module has high frequency circuits. The sufficient suppression to the electromagnetic interference should be done by the system manufa cturers. The grounding and shielding methods is important to minimize the interference.
(d) The cables between TV SET connector and Control PBA interface cable should be connected directly to have a minimized length. A longer cable between TV SET connector and Control PBA interface cable maybe operate abnormal display
(e) Recommend to age for over 1 hour at least in the state, which the product is driving initially to stabilize the characteristic of the initial TFT.
(f) Response time depends on the temperature.( In Lower temperature, it becomes longer)